Thought this might be of use to someone, when I was looking for info on programming the Sevcon Gen4 I found all the software and manuals here http://www.heinzmann.com/en/electric-an ... ontrollers
Also I found that the IXXAT canbus pci cards are easier to find at good prices, I picked one up for $100 and the drivers are included in the Sevcon software package. Not as portable as the usb dongles, but fine for in the workshop.
I've probably put this in the wrong section, feel free to move it.
Charles
My new project
Re: My new project
Starting to put it all back together after painting. I always find nice new paint shows up anything not in decent condition, so end up replacing nuts, bolts etc, and will have to tidy the wheels some time.
- Attachments
-
- bike281212.jpg (97.94 KiB) Viewed 36602 times
Re: My new project
looking good
Re: My new project
Plodding along slowly, though with this weather not in any rush. Well I decided that as an incentive to figure out Sevcon programming, I would swap over from the Kelly unit before I get it MOT'd. I was quite surprised at the weight of the heatsink, I thought aluminium was light! Probably a bit of overkill considering the power rating of the unit.
I'm happy with the basic motor config. John at Motoenergy gave me most of the electrical specs. I've just measured the back emf constant Ke by running the motor up with an electric drill, and it calculated as 0.022.
So should be ready to give it a run soon. Everybody I chat to says it's pretty well impossible to do any harm to the controller, as it has so many fail safes, we will see!
I still can't find any good info for setting up the regen, but not important for the moment.
I'm happy with the basic motor config. John at Motoenergy gave me most of the electrical specs. I've just measured the back emf constant Ke by running the motor up with an electric drill, and it calculated as 0.022.
So should be ready to give it a run soon. Everybody I chat to says it's pretty well impossible to do any harm to the controller, as it has so many fail safes, we will see!
I still can't find any good info for setting up the regen, but not important for the moment.
- Attachments
-
- Bike Sevcon.jpg (106.39 KiB) Viewed 36587 times
Re: My new project
Quality work. Looking forward to the next phase.
In these road conditions, (+0.5 to +6 degrees C, inc. a 1/2 mile 10-15% uphill), I roughly estimate my 64 Turnigys lose maybe 10% of their range over the spring and autumn distances
All the best
Ed
In these road conditions, (+0.5 to +6 degrees C, inc. a 1/2 mile 10-15% uphill), I roughly estimate my 64 Turnigys lose maybe 10% of their range over the spring and autumn distances
All the best
Ed
Re: My new project
Ed
I'm surprised it's that much. Do the batteries generate much heat with normal use? Are you starting with batteries at room/garage temperature.
It's been a super day today, but temperature dropping rapidly now, so the morning should be pretty dangerous.
I do find wiring very therapeutic, especially the thick stuff. I've run out of thin, so waiting for Vehicle Wiring Products to deliver so I can get on with the control wiring.
Regards
Charles
I'm surprised it's that much. Do the batteries generate much heat with normal use? Are you starting with batteries at room/garage temperature.
It's been a super day today, but temperature dropping rapidly now, so the morning should be pretty dangerous.
I do find wiring very therapeutic, especially the thick stuff. I've run out of thin, so waiting for Vehicle Wiring Products to deliver so I can get on with the control wiring.
Regards
Charles
- Attachments
-
- bike sevcon wiring.jpg (61.06 KiB) Viewed 36585 times
Re: My new project
starting from + 2.5 degrees C AAT on the driveway, 5.8 degrees C surface of battery-pack box, 7pm that evening. hope it's not a loss of overall battery performance...
cheers
ed
cheers
ed
Re: My new project
Well it's taken me a week, going gradually nuts, but finally got the Sevcon controller to play ball. I still haven't figured out regen braking yet, but that's not a problem. I haven't had it out for a ride yet, but the motor is so much quieter. It makes a nice gentle hum as it starts, rather than the loud clicking noise the Kelly unit made.
Better get on with tidying the control wiring up now I know it works.
Better get on with tidying the control wiring up now I know it works.
Re: My new project
The Kelly I used on the Fiat Cinquecento EV would not start on any less than 5% "startup-throttle" (set using my laptop)
5% gave a sharp click and a slight jerk on moving off, no matter how gently I increased the pedal pressure from nil
Looking forward to hearing how it runs on the road
All the best
Ed
5% gave a sharp click and a slight jerk on moving off, no matter how gently I increased the pedal pressure from nil
Looking forward to hearing how it runs on the road
All the best
Ed
Re: My new project
Well finally got round to MOTing and getting her on the road. I've now got to go to the DVLA and get my new tax disc swapped for a proper free electric one. They did mention that they may want a letter from the garage that fitted the engine, so that would be me then!
Anyway, I managed 40 miles so far and still had about 20% left, so should hit my 50 mile range target. I'm still setting up the neutral brake regen on the Gen4 controller, quite fiddly to get just the right amount of braking so that it feels like normal engine braking.
Only problem now is the weather is so poor!
Anyway, I managed 40 miles so far and still had about 20% left, so should hit my 50 mile range target. I'm still setting up the neutral brake regen on the Gen4 controller, quite fiddly to get just the right amount of braking so that it feels like normal engine braking.
Only problem now is the weather is so poor!
- Attachments
-
- Bike1.jpg (89.03 KiB) Viewed 36556 times
Return to “Electric Motor Bikes”
Who is online
Users browsing this forum: No registered users and 4 guests