Hello,
I diagnosed my newly purchased Blingo with ECU light on.
Gives code D4 - permament error ECU parameters
evlite manual says as solution: reprogram ECU parameters...
anybody had that problem and know what to do?
car drives/behaves normally... many thanks
previous owner told me that it might be insulation error (ECU light) but that's not the case...
D4 error in Blingo
D4 error in Blingo
evcar.pl - www.electrique.pl
Re: D4 error in Blingo
mmmm new one to me, sounds like it needs to be hooked up to a Diag or Planet software and have something done to it
ChrisB
ChrisB
I reject reality and substitute my own !!!!!!
Re: D4 error in Blingo
I tested van today. Gave me 35 miles range then light came for charging.
power meter was at 20%.
I used headlights all the time, webasto and radio. And I drove at variable speeds 30-50mph quite carefully (eco meter always green) on rather flat surface.
Temperature outside was around 2-3 degrees celcius.
Nothing bad happened, but ecu light remains on all the time with D4 code.
power meter was at 20%.
I used headlights all the time, webasto and radio. And I drove at variable speeds 30-50mph quite carefully (eco meter always green) on rather flat surface.
Temperature outside was around 2-3 degrees celcius.
Nothing bad happened, but ecu light remains on all the time with D4 code.
evcar.pl - www.electrique.pl
Re: D4 error in Blingo
I know how to remove D4 error but I'm unsure of one thing.
I have LEXIA software and interface which works well.
And info giving on SAGEM is: "recode parameters".
There is "telecoding" traction parameters option and I can choose one of three:
14A
13A
10A
whichever I choose - SAGEM is coded and then D4 error (and fault light) is gone.
I've chosen 14A, and then sagem parameters is set to 14A. I can always change that.
But I'm unsure which is correct... Shall I put screen capture here?
Lexia software is great - much more powerful than evLite
I have LEXIA software and interface which works well.
And info giving on SAGEM is: "recode parameters".
There is "telecoding" traction parameters option and I can choose one of three:
14A
13A
10A
whichever I choose - SAGEM is coded and then D4 error (and fault light) is gone.
I've chosen 14A, and then sagem parameters is set to 14A. I can always change that.
But I'm unsure which is correct... Shall I put screen capture here?
Lexia software is great - much more powerful than evLite
evcar.pl - www.electrique.pl
Re: D4 error in Blingo
The amp setting is to restrict the power to the supply. So uk vehicles are set at 13amp so that our power points dont get overloaded.
Grumpy-b
Grumpy-b
Re: D4 error in Blingo
Thanks! I thought it has something to do with charging van
I use caravan 16A socket anyway... so shall I leave 14A? Will load a little bit faster
or leave at 13A to be on safe side.
I checked other Berlingos - they ALL have "unknown parameters" set and there is suggestion to "recode" them.
Also the others don't have D4 error at all....
I use caravan 16A socket anyway... so shall I leave 14A? Will load a little bit faster
or leave at 13A to be on safe side.
I checked other Berlingos - they ALL have "unknown parameters" set and there is suggestion to "recode" them.
Also the others don't have D4 error at all....
evcar.pl - www.electrique.pl
Re: D4 error in Blingo
I telecoded 14A to one Berlingo which gives D4 error.
Now error is gone (and won't coming back) but I have feeling that acceleration is not as good as before and reaction for acceleration pedal is a bit delayed... could it that be any affect?
Now error is gone (and won't coming back) but I have feeling that acceleration is not as good as before and reaction for acceleration pedal is a bit delayed... could it that be any affect?
evcar.pl - www.electrique.pl
Return to “Citroen Berlingo Electrique or other PSA vehicles”
Who is online
Users browsing this forum: No registered users and 6 guests